Vinyl - Vinyl Other - Crain Tools

No. 280 H.D. Air Lifter

The Air Lifter moves heavy appliances up to 800 lbs. by generating high pressure jets through its perforated rubber load plates. Slide the air plates under the load, turn on the blower, adjust the convenient lift control valve, and the air plates inflate to lift the load. The plates glide over hard surfaces such as tile or hardwood without scratching. Comes with 4 smooth polypropylene pads which allow the plates to move over carpet. Saves time and reduces the risk of damaging new floors and injuries! The kit includes: 2 air plates, 2 horsepower blower with shoulder strap, lift control valve, T-connector, 3 hoses, 4 carpet pads, and protective carrying bag. Volts: 120VAC – Amps: 7.5. Net weight: 33 lbs.

No. 017 Metal Skat Skate Dolly Set

Crain Skat Skates are a pair of heavy-duty dollies that are adjustable in length for moving a wide variety of furniture and appliances. Each dolly in the set adjusts in length from 24″ to 32″. Each dolly has two 8″ x 10″ load pads and four pivoting casters beneath each pad. The 16 total casters allow the load to be easily moved or to change direction. The steel load bearing plates and telescoping tubes are welded together for durability. The soft urethane casters won’t scratch or dent most floors. The maximum load capacity for the set is 1,000 lbs. Set weight: 20 lbs.

No. 018 Tile Dolly

This dolly is specifically designed for moving heavy boxes of VCT and other tile around the jobsite. It rolls and turns with up to five boxes of VCT on its deck or approximately 300 lbs. of material. It has five swiveling casters including one in the middle to help it turn and rotate. The casters have hardened steel brackets and soft urethane rollers that tend not to scratch most floors. The rugged 11″ x 16″ reinforced plastic deck includes a handle for grabbing and pulling. Maximum capacity: 300 lbs. Net weight: 3 ³/₄ lbs.

No. 015 18″ Vinyl Dolly

These 18″ dollies are designed for moving and unrolling heavy rolls of vinyl on the jobsite up to 16″ in diameter. Each of the three 18″ long heavy gauge tubular steel rollers is mounted on double ball bearings to form a rolling bed for the material. Simply pull on the sheet, and the material feeds off the roll. The dolly has four non-marking rubber wheels mounted on the sturdy cast aluminum end frames which permit the dolly to be easily moved even when loaded. Net weight: 13 lbs.

No. 016 36″ Vinyl Dolly

These 36″ dollies are designed for moving and unrolling heavy rolls of vinyl on the jobsite up to 16″ in diameter. Each of the three 36″ long heavy gauge tubular steel rollers is mounted on double ball bearings to form a rolling bed for the material. Simply pull on the sheet, and the material feeds off the roll. The dolly has four non-marking rubber wheels mounted on the sturdy cast aluminum end frames which permit the dolly to be easily moved even when loaded. Net weight: 20 lbs.

No. 143 Disposable Adhesive Syringe

This large capacity 2 oz. syringe with 2 inch long 13 gauge needle is used for repairing bubbles in glued-down flooring materials like carpet and vinyl. It delivers adhesive to the problem spot leaving a minimal puncture. Use with liquid adhesive such as latex. Not for use on hardwood repairs with thick adhesives such as hardwood adhesive. State law prohibits sale in these states: Connecticut, Maryland, New Jersey, Delaware, Massachusetts, New York, Maine, New Hampshire, Rhode Island.

No. 334 6′ Professional Straight Edge

The six foot Professional Straight Edge provides the accuracy needed for making seams in sheet vinyl and like materials. It is precision ground on each of its edges for straightness with accuracy of +/-.003″. It establishes straightness along a first edge of a seam so that the other edge can be underscribed using the first edge as a guide. This straight edge is also made of special spring steel that will return to its flat condition even after being bent. It has one end formed at a 45° angle for pattern work, and is painted blue to reduce rust. Dimensions: 6′ x 3″ x ¹/₈“. Net weight: 6 ¹/₂ lbs.

No. 334S 4′ Professional Straight Edge

The four foot Professional Straight Edge provides the accuracy needed for making seams in sheet vinyl and like materials. It is precision ground on each of its edges for straightness with accuracy of +/-.003″. It establishes straightness along a first edge of a seam so that the other edge can be underscribed using the first edge as a guide. This straight edge is also made of special spring steel that will return to its flat condition even after being bent. It has one end formed at a 45° angle for pattern work, and is painted blue to reduce rust. Dimensions: 4′ x 3″ x ¹/₈“. Net weight: 4 lbs.

No. 116 18″ Flexible Straight Edge

This 18″ long steel straight edge is made from a thin strip of flexible spring steel. It bends easily as necessary to work around obstructions, but afterwards will return to its original flat condition. It works well in tight areas like doorways, corners, and closet areas. Includes a 45° angle on one end for template work, and a hanging hole on the opposite end. Finished with bright red paint to help prevent rust. Dimensions: 18″ long x 2″ wide x ¹/₃₂” thick. Net weight: 4 oz.

No. 117 32″ Flexible Straight Edge

This 32″ long steel straight edge is made from a thin strip of flexible spring steel. It bends easily as necessary to work around obstructions, but afterwards will return to its original flat condition. It works well in tight areas like doorways, corners, and closet areas. Includes a 45° angle on one end for template work, and a hanging hole on the opposite end. Finished with bright red paint to help prevent rust. Dimensions: 32″ long x 2″ wide x /₃₂” thick. Net weight: 6 oz.

No. 118 39″ Flexible Straight Edge

This 39″ long steel straight edge is made from a thin strip of flexible spring steel. It bends easily as necessary to work around obstructions, but afterwards will return to its original flat condition. It works well in tight areas like doorways, corners, and closet areas. Includes a 45° angle on one end for template work, and a hanging hole on the opposite end. Finished with bright red paint to help prevent rust. Dimensions: 39″ long x 2″ wide x /₃₂” thick. Net weight: 7 oz.

No. 912 12” x 8” Steel Square

This 12″ x 8″ steel square is useful for patterned vinyl flooring layout work. The legs include rulers on the front and back side marked in ¹/₁₆” graduations that are permanently impressed in the steel. Made from hardened steel and coated with a clear finish that resists rust. Dimensions – body: 12″ long x 1 ¹/₂” wide, tongue: 8″ long x 1″ wide. Net weight: 8 oz.

No. 915 24” x 16” Steel Square

A 24″ x 16″ steel square is useful for patterned vinyl flooring layout work. The legs include rulers on the front and back side marked in ¹/₈” graduations that are permanently impressed in the steel. Made from hardened steel and coated with a clear finish that resists rust. Dimensions – body: 24″ long x 2″ wide, tongue: 16″ long x 1 ¹/₂” wide. Net weight: 1 ¹/₂ lbs.

No. 340 Selvage Trimmer

This tool trims off the factory selvage, so that the sheet can be accurately scribed and seamed. When the selvage edge of the material is inserted into the guidance slot, the blade is automatically positioned at the proper distance from the edge for trimming off the selvage. The replaceable U-shaped blade makes a clean, square cut that will be perpendicular with the floor. Simply pull the tool through the material and the selvage is removed. Blades: No. 341 – one each or No. 342 – three each. Net weight: 10 ¹/₂ oz.

No. 341 Selvage Trimmer Repl. Blade (1)

Includes one each replacement blade for the No. 340 Selvage Trimmer. Trims the factory selvage so the sheet can be accurately scribed and seamed. The U-shaped blade ensures a smooth, accurate, square-edged cut that will be perpendicular to the floor to match an adjacent edge. Includes one replacement blade only. Trimmer not included. Pack weight: ¹/₄ oz.

No. 342 Selvage Trimmer Repl. Blades (3)

Includes a pack of three each replacement blades for the No. 340 Selvage Trimmer. Trims the factory selvage so the sheet can be accurately scribed and seamed. The U-shaped blade ensures a smooth, accurate, square-edged cut that will be perpendicular to the floor to match an adjacent edge. Includes three replacement blades only. Trimmer not included. Pack weight: ¹/₄ oz.

No. 320 Vinyl Wall Trimmer

This tool accurately trims sheetgoods net to the wall. Adjustable front and rear guides provide precise control. The front bar holds that material in position against the wall. The rear guide keeps the trimmer running parallel with the wall for smooth trimming action. The low profile hand contours assist with keeping the tool flat on the floor as it is pushed along the wall. Comes with one hook blade. Blades: No. 321 Vinyl Wall Trimmer Blades (3). Net weight: 8 oz.

No. 321 Vinyl Wall Trimmer Blades (3)

Includes a pack of three hook blades for the No. 321 Vinyl Wall Trimmer. The reversible blade includes two cutting hook edges. The blades come in a plastic box with a hinged lid for storage. Blade dimensions: length: 2.30″, width: .50″, thickness: .025″. Pack weight: 1 oz.

No. 247 Multi-Purpose Wall Trimmer

This trimmer has a rounded wall runner which allows it to trim vinyl sheetgoods net to the wall. The tool can also trim cut pile carpets. When trimming vinyl, the tool comes with an anti-friction boot to prevent it from scratching. The spring-loaded center knob for height adjustment is easy to use. Takes either slotted razor blades or hook blades. Slotted razor blades work well on vinyl, while hook blades work well on cut pile carpet. Blades: No. 308 Slotted Razor Blades or No. 996X Hook Blades. Net weight: 2 lbs.

No. 270 Outside Silver Corner (Each)

These silver metal corners cover a sheet vinyl outside corner. They cover up problems at the corner, and are an excellent solution for repairs. They are made approximately 6 inches long to cover the corner from floor height up to 6 inches if necessary. The bottom portion is contoured to the shape of a standard cove. They are easily trimmed to a shorter height using a pair of snips. They can be adhered to vinyl, linoleum, or like sheetgoods using a hot glue gun. Net weight: ¹/₄ oz. per corner.

No. 271 Inside Silver Corner (Each)

These silver metal corners cover a sheet vinyl inside corner. They cover up problems at the corner, and are an excellent solution for repairs. They are made approximately 6 inches long to cover the corner from floor height up to 6 inches if necessary. The bottom portion is contoured to the shape of a standard cove. They are easily trimmed to a shorter height using a pair of snips. They can be adhered to vinyl, linoleum, or like sheetgoods using a hot glue gun. Net weight: ¹/₄ oz. per corner.

No. 272 Outside Gold Corner (Each)

These gold metal corners cover a sheet vinyl outside corner. They cover up problems at the corner, and are an excellent solution for repairs. They are made approximately 6 inches long to cover the corner from floor height up to 6 inches if necessary. The bottom portion is contoured to the shape of a standard cove. They are easily trimmed to a shorter height using a pair of snips. They can be adhered to vinyl, linoleum, or like sheetgoods using a hot glue gun. Net weight: ¹/₄ oz. per corner.

No. 273 Inside Gold Corner (Each)

These gold metal corners cover a sheet vinyl inside corner. They cover up problems at the corner, and are an excellent solution for repairs. They are made approximately 6 inches long to cover the corner from floor height up to 6 inches if necessary. The bottom portion is contoured to the shape of a standard cove. They are easily trimmed to a shorter height using a pair of snips. They can be adhered to vinyl, linoleum, or like sheetgoods using a hot glue gun. Net weight: ¹/₄ oz. per corner.

No. 745 Deluxe 750° Heat Gun w/Case

This flameless electric heat gun can deliver hot air up to 750°F for softening, forming, and more easily cutting sheet vinyl, VCT tile, and like materials. The adjustable intake cover controls output temperature between approximately 500°F – 750°F. The high speed fan puts out 27 cubic feet per minute of hot air. The three way switch switches the gun between off, cold, or hot, with cold being used for properly cooling the element to extend its useful life. The replaceable mica element and brushes of this heat gun are some of the longest lasting available. Elements are easily replaceable without tools (replacement element: Part No. 1745-030). Comes with adjustable stand and protective carrying case. Operates on 120 Volts, 1440 Watts, 12 Amps. Net weight 7 ³/₄ lbs.

No. 745K Deluxe Gun Universal Case

This carrying case holds Crain Nos. 745 and No. 995 Deluxe Heat Guns. Also holds all previous Crain Nos. 740 and No. 990 Deluxe Heat Guns. This rugged blow-molded plastic carrying case has a custom formed interior to support and protect the heat gun during transportation and storage. Made with dual latches, piano-style hinges, and recessed handle for durability. Heat gun not included. Net weight: 4 lbs.

No. 995 Deluxe 1000° Heat Gun w/Case

This flameless electric heat gun can deliver hot air up to 1000°F for softening, forming, and more easily cutting sheet vinyl, VCT tile, and like materials. The adjustable intake cover controls output temperature between approximately 750°F – 1000°F. The high speed fan puts out 27 cubic feet per minute of hot air. The three way switch switches the gun between off, cold, or hot, with cold being used for properly cooling the element to extend its useful life. The replaceable mica element and brushes of this heat gun are some of the longest lasting available. Elements are easily replaceable without tools (replacement element: Part No. 1995-450). Comes with adjustable stand and protective carrying case. Operates on 120 Volts, 1800 Watts, 15 Amps. Net weight 7 ³/₄ lbs.

No. 751 Thriftline Heat Blo Gun

This inexpensive 1200 watt heat gun produces adjustable hot air from 250° – 1000°F. Temperature is adjustable by turning a large knob at the back of the gun. A three- position switch controls the power and amount of air output at high, low or power off. The pistol-grip handle is designed to stand the gun upright to prevent damaging the floor. Net weight: 2 lbs.